23,000 BTU Portable Kerosene Heater, Model# CV-2230

$119.98

Multiroom, omnidirectional kerosene heater boasts many safety features and push button start. Operates 12 hours on built-in fuel tank. Provides emergency heating during power failures, as no electricity is required. Not approved for use in Massachusetts. BTU Output: 23,000, Heating Capability (sq. ft.): 1,000, Full Load Run Time (Hours): 12, Fuel Capacity (gal.): 1.9, Fuel Type: Kerosene, Igniter: Push button, Cart: No, Dimensions L x W x H (in.): 18 4/5 x 18 4/5 x 27 Safety grills protect against burns Auto safety shutoff for tipovers Includes 2 D batteries for ignition and siphon pump UL listed Check local codes and ordinances for approved installation and usage Replacement wick available, Item# 173407 [Read more]

Store: Northern Tool and Equipment

Brand: Northern Tool and Equipment

Fahrenheat Electric 5120 BTU Baseboard Heater, Model# FBE15002

$74.98

This slim profile, quiet, energy efficient heater makes it ideal for office workstations, building entrances, bedrooms, garages and basements. Two settings: 1000 and 1500 Watts with 2560 or 5120 BTU and 6.3 or 12.5 Amps. A full length sensor turns heater off if blocked. Steel unitized body, neutral off-white finish and built in carrying handles. Built-in thermostat lets you regulate heat. Six-foot cord for 120 Volt power. 7 1/2in.H x 5 1/2in.D x 47in.L. UL Listed. U.S.A. Primary Heating Application: Baseboard, BTU Output: 3,413 or 5,120, Volts: 120, Amps: 8.3 or 12.5, Watts: 1,000 or 1,500, Blower Included: No, Heat Settings: 2, Thermostat Included: Yes, Power Cord (ft.): 6, Plug Type: Polarized, Receptacle Type Required: Standard 120v, Remote Included: No, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: Yes Constructed of 24 gauge steel [Read more]

Store: Northern Tool and Equipment

Brand: Fahrenheat

Tower Space Heater - 1500 Watt, 5120 BTU, Model# 02144

$34.00

This 5120 BTU tower heater is perfect for stashing under your desk or keeping cozy on the couch or in bed. A ceramic heating element generates up toasty warmth with three heat settings. Conveniently adjustable with the included remote control. Also features tip-over, timer and thermal cutoff safety devices. Primary Heating Application: Portable, BTU Output: 5,120, Volts: 120, Amps: 12.5, Watts: 1500, Blower Included: No, Heat Settings: Three, Thermostat Included: Yes, Power Cord (ft.): 6ft, Plug Type: Polarized, Remote Included: Yes, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: Yes, Dimensions W x D x H (in.): 8 1/2 x 10 1/4 x 23 [Read more]

Store: Northern Tool and Equipment

Brand: Northern Tool and Equipment

Ouellet Electric Baseboard Heater - 1250 Watt, Model# OFM1252BL

$61.99

The Ouellet Electric Baseboard Heater provides a compact design that delivers high performance and strength while easing installation. Primary Heating Application: Baseboard, Volts: 120, Amps: 10.42, Watts: 1,250, Power Cord (ft.): Must be hardwired, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 58 x 3 x 6 Steel tubular heating element with aluminum fins includes with linear high-limit temperature control with automatic reset Compact design delivers high performance and strength while eliminating use of a furring strip during installation Features sturdy 22-gauge steel body with 20-gauge front panel Available in White in epoxy/polyester powder paint; may be repainted with any interior paint Optional thermostat kit can be installed at either end [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

Firesense Hanging Stainless Steel Halogen Patio Heater - 1500 Watt, Model# 60405

$149.99

This halogen patio heater runs on regular household electric current and is substantially less expensive to operate than a propane patio heater. Creates no harmful emissions or toxic residuals, so it can be used indoors and out. Heats objects directly, rather than wasting energy by heating the air. Achieves 100% operation within seconds of activation. Primary Heating Application: Outdoor, Volts: 110, Watts: 700 / 800 / 1,500, Heat Settings: 3, Dimensions W x D x H (in.): 22 7/8 x 22 7/8 x 12 Three heat settings ETL approved [Read more]

Store: Northern Tool and Equipment

Brand: Fire Sense

DynaGlo Delux Multi-Fuel Forced Air Heater - 650,000 BTU, Model# RMC-KFA650TDGD

$2,199.98

This DynaGlo Delux Multi-Fuel Forced Air Heater produces 650,000 BTU to heat areas up to 13,500 square feet. Ideal for use in outdoor construction sites, agricultural buildings, industrial workspaces and more. Easily portable to move from one site to the next. CSA approved; UL approved motor. BTU Output: 650,000, Heating Capability (sq. ft.): 13,500, Blower (CFM): 3,600, Heat Settings: Yes, Full Load Run Time (Hours): 10, Fuel Capacity (gal.): 50, Fuel Type: 1K kerosene or diesel, Fuel Consumption (gal./hr.): 4.9, Igniter: Pushbutton electric, Thermostat Included: Yes, Cart: Yes, Dimensions L x W x H (in.): 48 3/4 x 30 3/4 x 48 3/4 Safety flame out sensor Durable commercial-grade product Separate fuel cap and exclusive run time fuel gauge Built-in comfort control thermostat TSTAT with digital room temp readout and digital diagnostics On/off power switch with LED error light 12in. flat-free solid wheels with threaded axle and cap nut [Read more]

Store: Northern Tool and Equipment

Brand: DynaGloDelux

Profusion Heat Wall-Mounted Convection Heater - 5120 BTU, 1500 Watts, Model# HC-09C15

$39.00

This Profusion Heat wall-mounted convection heater mounts on the wall and radiates 5120 BTU of heat into the air and directly into the walls themselves. Sheathed aluminum heating element is safe and silent. Includes wall mount. Primary Heating Application: Wall heater, BTU Output: 5,120, Volts: 240, Amps: 6.25, Watts: 1,500, Heat Settings: 1, Thermal Cutoff Safety Device: Yes, Dimensions W x D x H (in.): 24 x 4 5/16 x 17 5/16 [Read more]

Store: Northern Tool and Equipment

Brand: ProFusion Heat

Mr. Heater Sun-Rite Tank-Top Propane Heater

$29.00

Whether youre backpacking, hunting, camping, fishing or on a picnic, youre going to need some help to beat the tough weather. Thats where the Sun-Rite heater comes in. It attaches directly on top of a 20 lb. propane cylinder and provides hours of powerful, soothing heat. Adjustable heat settings let you control the temperature as well as fuel consumption. BTU Output: 8,000 - 15,000, Primary Heating Application: Outdoors, Heat Settings: 3, Fuel Type: Propane Heater automatically shuts down at a loss of flame [Read more]

Store: Northern Tool and Equipment

Brand: Northern Tool and Equipment

Comfort Zone Infrared Quartz Heater - 1500 Watts, Oak, Model# 125128

$199.00

The Comfort Zone Deluxe Wood Cabinet Infrared Quartz Heater saves you money by cutting down on the need for gas or oil to heat a room or area in your home. Its 5120 BTU output heats a 130 sq. ft. area with the help of the included blower. Remote controlled thermostat lets you set and maintain the temperature you need through three heat settings. Furniture-grade wood cabinet in oak matches any decor. Primary Heating Application: Infrared, BTU Output: 5,120, Heating Capability (sq. ft.): 130, Volts: 120, Amps: 12.5, Watts: 1,500, Blower Included: Yes, Heat Settings: 3, Thermostat Included: Yes, Receptacle Type Required: 3-prong grounded, Remote Included: Yes, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: Yes, Dimensions W x D x H (in.): 17 5/8 x 12 7/8 x 20 6 high-power quartz infrared emitters with 3 copper heat exchangers for powerful heat production Digital thermostat with 59 -86 F range 12-hour Auto-On/Auto-Off timer Long-lasting galvanized interior heat chamber Backlit LCD display 6ft. rounded AWG cord with convenient storage works with all standard wall outlets Swivel casters for easy movement from room to room Lifetime washable cool air intake filter Stay-cool exterior wood case is safe around children and pets Safety temperature overheat cut-off switch Safety tip-over power cut-off switch Full-function remote control [Read more]

Store: Northern Tool and Equipment

Brand: Northern Tool and Equipment

Lifesmart Amish-Style Heater with Air Filter - 1500 Watts, Model# LS-P-1500-6

$249.99

This Lifesmart Amish-Style Heater with Air Filter helps you save big on heating bills while creating a healthier, more comfortable environment. Heating Capability (sq. ft.): 1,200, Volts: 110, Watts: 1,000 / 1,500, Remote Included: Yes Warms up to 1200 square feet plus filters bacteria, viruses, mold, mildew and other harmful organisms Removes contamination caused by furnaces, woodstoves, oil space heaters and more Safe to use around kids and pets Six quartz infrared elements for greater heat transfer UL listed [Read more]

Store: Northern Tool and Equipment

Brand: Lifesmart

Duraflame Infrared Quartz Heater - 5200 BTU, 1500 Watts, 1000 Sq. Ft. Heating Area, Model# 10HM1342EPC

$249.99

Reduce your dependence on gas heat this winter by adding this infrared quartz heater to your arsenal. It produces 6000 BTU, enough to heat a 1000 sq. ft. area with the help of the included blower. The remote control thermostat lets you set and maintain the temperature you need, from 55 F to 97 F. The air purifying function further enhances the quality of any space. A timer function causes the heater the automatically turn itself off, a great way to save on energy costs. Primary Heating Application: Infrared, BTU Output: 5,200, Heating Capability (sq. ft.): 1,000, Volts: 120, Amps: 12.5, Watts: 1,500, Blower Included: Yes, Heat Settings: Variable, Thermostat Included: Yes, Power Cord (ft.): 6, Plug Type: 3-prong, Remote Included: Yes, Thermal Cutoff Safety Device: Yes, Dimensions W x D x H (in.): 14 3/4 x 20 x 17 3/4 Easily removed filter can be cleaned with warm water or a vacuum Flocked heater grill stays cool to the touch Includes overheat shutoff device [Read more]

Store: Northern Tool and Equipment

Brand: Duraflame

ProFusion Halogen Heater - 3-Setting, Pole-Mounted

$69.00

This versatile ProFusion 3-setting (500/1000/1500 Watt), adjustable 3-arm pole-mount heater lets you put heat where needed. Design provides 360 coverage for surround heating or to direct heat to a specific area. Radiant halogen elements heat objects and people, not air, operating silently without moving parts. Primary Heating Application: Outdoor, Heating Capability (sq. ft.): 5,200, Volts: 120, Amps: 12.5, Watts: 1500, Heat Settings: 3, Power Cord (ft.): 6, Remote Included: No, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: Yes, Dimensions W x D x H (in.): 22.4 x 13 x 12.2 Durable metal housing makes heater ideal for indoor use in workshops or garages Can work outdoors as well Aluminum mesh and iron-coated covers provide durability Weather-protected covered switch allows use in wet conditions ETL approved Parasol not included [Read more]

Store: Northern Tool and Equipment

Brand: ProFusion Heat

BioSmart In-Wall Infrared Heater - 2800 BTU, Model# BIO-500F

$299.98

This BioSmart in-wall infrared heater delivers powerful heating in a slim-lined package. Up to 160 F of therapeutic infrared heat. The chassis stays cool to the touch with insulation that exceeds all government and independent safety standards. Must be hardwired. Works with any 12-24V thermostat (not included). Overheat safety cutoff device. Primary Heating Application: Wall heater, BTU Output: 2,800, Heating Capability (sq. ft.): 200, Watts: 500, Blower Included: Yes, Thermostat Included: No, Remote Included: No, Thermal Cutoff Safety Device: Yes, Dimensions W x D x H (in.): 4 1/2 x 4 x 18 [Read more]

Store: Northern Tool and Equipment

Brand: Comfort Zone

Fahrenheat Portable Electric Hydronic Heater, Model# LFP6152

$179.99

Enjoy safe, portable comfort from floor to ceiling in bathrooms, offices and other similar-sized areas in your home. You choose from 2 settings for just the right amount of warmth you want: 750 or 1500 Watts. The Smart Stat thermostat maintains a desired comfort level, depending on setting. Heats evenly to reduce room temperature variations. Attractive, contemporary styling in a durable, steel unitized body. UL listed. Primary Heating Application: Portable, BTU Output: 2,560 or 5,120, Volts: 120, Amps: 6.3/12.5, Watts: 750, 1,500, Blower Included: No, Heat Settings: 2, Thermostat Included: Yes, Power Cord (ft.): 6, Remote Included: No, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: No Lighted on/off switch Wattage indicator lights one light when heat is on low; 2 lights when heat is on high Permanently sealed silicon oil-filled element Energy efficient since 100% of the heat is convected into the room and stored-up heat from the element keeps radiating warmth between power-on cycles Tuck-away carrying handle [Read more]

Store: Northern Tool and Equipment

Brand: Fahrenheat

Mr. Heater Natural Gas Heater - 100,000 BTU, Model# F191824

$659.98

Provides plenty of heat even during power outages requires no electricity. Thermostat is included for comfort control. For indoor use. Recommended for buildings with 19ft. to 22ft. ceilings. AGA design certified. U.S.A. Primary Heating Application: Garage, workshop, Vent-Free: No, BTU Output: 100,000, Blower Included: No, Fuel Type: Natural gas, Thermostat Included: Yes, Remote Included: No Efficient Infrared Heat - Directly heats people and objects which in turn heats surrounding air to desired temperature Economical - No electricity required. Heats during power outages Convenient - Easy to operate and install; All necessary brackets and hardware included Quiet, clean, odor-free operation Instant Heat - Includes adjustable thermostat for individually controlled warmth CSA certified [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Mr. Heater Double Propane Heater With Piezo Ignitor - 8,000-28,000 BTU, Model MH24TS

$109.98

In the great outdoors, FAST clean-burning LP heaters provide hundreds of uses. Need more than two burners? Order our item #1726 or #1729 heater. All are equipped with a safety shutoff valve and adjustable fingertip control. Heaters have a hi-med-low regulator and use a 20-lb. propane tank. U.S.A. Vent-Free: No, BTU Output: 28,000, Primary Heating Application: Garage, workshop, Heat Settings: 6, Fuel Type: Propane 1 lb disposable, Fuel Consumption (gal./hr.): 15 hours per 20-lb. tank on HI, Igniter: Matchless piezo push-button, Thermostat Included: No, Remote Included: No, Oxygen Depletion Sensor: No Variable BTUs - 8, 12, 14, 16, 24 and 28,000 BTU/HR Adjustable Heat Control - Hi, Med, Lo regulator; Operate one or two burners at a time Hi: 28,000 BTUS Per Hour Low: 8,000 BTUS Per Hour Safety: Fuel valve shuts off if flame goes out Clearance to Combustibles: 24in. from centerline of heater to floor and 30in. to sides and above heater For outdoor use only [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Mr. Heater Propane-to-Natural Gas Conversion Kit - 45,000 BTU, Model# 60066

$24.98

This Mr. Heater Propane-to-Natural Gas Conversion Kit quickly and easily converts a Mr. Heater 45,000 BTU Big Maxx heater from propane to natural gas. Common Usage: Conversion kit, Style: Liquid propane to natural gas, Works With: Heater 45,000 BTU Big Maxx heater Quickly and easily converts a Mr. Heater 45,000 BTU Big Maxx heater from propane to natural gas [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Solaria Electric Infrared Heater - Commercial-Grade, Indoor/Outdoor, 6000 Watts, 240 Volts, Model# SALPHAH2-60240S

$949.98

This Solaria commercial-grade Electric Infrared Heater uses advanced short wave infrared heating technology to instantly warm people and objects, not just air, with safe, clean, dependable heat. Primary Heating Application: Commercial, BTU Output: 20,488, Heating Capability (sq. ft.): 400, Volts: 240, Amps: 25, Watts: 6,000, Power Cord (ft.): 6, Dimensions W x D x H (in.): 47 x 9 x 5 1 / 2 Super-efficient operation costs just pennies per hour, converting 92% of consumed energy into comfortable heat Weatherproof casing is safe for use indoors or outdoors Heats instantly with no initial warm up time Modular design allows for easily adjusting heat loads Silent, odorless operation with no risk of combustion Powder-coated aircraft aluminum construction provides rugged durability Wall or ceiling mount design saves space no bulky propane gas containers required [Read more]

Store: Northern Tool and Equipment

Brand: Solaira Heaters

Mr. Heater Single Heater With Piezo Ignitor - 8,000-14,000 BTU, Model# MH12TS

$59.99

In the great outdoors, FAST clean-burning LP heaters provide hundreds of uses. Need more than one burner? Order our item #1727 or #1729 heater. All are equipped with a safety shutoff valve and adjustable fingertip control. Heaters have a hi-med-low regulator and use a 20-lb. propane tank. U.S.A. Vent-Free: No, BTU Output: 14,000, Primary Heating Application: Garage, workshop, Heat Settings: 3, Fuel Type: Propane, Fuel Consumption (gal./hr.): 30 hours per 20-lb. tank on HI, Igniter: Matchless piezo push-button, Thermostat Included: No, Remote Included: No, Oxygen Depletion Sensor: No Variable BTU: 8, 12 and 14,000 BTU Adjustable Heat Control: Hi, Med, Lo regulator Hi: 14,000 BTU per hour Low: 8,000 BTU per hour Safety: Fuel valve shuts off if flame goes out Clearance to Combustibles: 24in. from centerline of heater to floor and 30in. to sides and above heater For outdoor use only [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Solaria Electric Infrared Heater - Commercial-Grade, Indoor/Outdoor, 1500 Watts, 240 Volts, Model# SALPHA15240S

$389.98

This Solaria commercial-grade Electric Infrared Heater uses advanced short wave infrared heating technology to instantly warm people and objects, not just air, with safe, clean, dependable heat. Primary Heating Application: Commercial, BTU Output: 5,122, Heating Capability (sq. ft.): 100, Volts: 240, Amps: 6.25, Watts: 1,500, Power Cord (ft.): 15, Receptacle Type Required: J box, GFI recommended, Dimensions W x D x H (in.): 9 x 5 1 / 2 x 17 Super-efficient operation costs just pennies per hour, converting 92% of consumed energy into comfortable heat Weatherproof casing is safe for use indoors or outdoors Heats instantly with no initial warm up time Modular design allows for easily adjusting heat loads Silent, odorless operation with no risk of combustion Powder-coated aircraft aluminum construction provides rugged durability Wall or ceiling mount design saves space no bulky propane gas containers required UL/CSA approved cord for safety [Read more]

Store: Northern Tool and Equipment

Brand: Solaira Heaters

Mr. Heater Sun-Rite Tank-Top Propane Heater - 30,000 BTU, Model# SR30T

$59.00

Whether youre backpacking, hunting, camping, fishing or on a picnic, youre going to need some help to beat the tough weather. Thats where the Sun-Rite heater comes in. It attaches directly on top of a 20 lb. propane cylinder and provides hours of powerful, soothing heat. Adjustable heat settings let you control the temperature as well as fuel consumption. BTU Output: 16,000 - 30,000, Primary Heating Application: Outdoors, Heat Settings: 3, Fuel Type: Propane Heater automatically shuts down at a loss of flame 30-52 hr. runtime on High on 20-lb. cylinder [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Mr. Heater Propane-to-Natural Gas Conversion Kit - 75,000 BTU, Model# 60071

$24.98

Common Usage: Conversion kit, Style: Propane to natural gas, Includes: 10 Pieces [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Mr. Heater Natural Gas-to-Propane Conversion Kit - 75,000 BTU, Model# 60067

$24.98

This Mr. Heater Natural Gas-to-Propane Conversion Kit quickly and easily converts a Mr. Heater 75,000 BTU Big Maxx heater from natural gas to propane. Common Usage: Conversion kit, Style: Natural gas to liquid propane, Works With: Mr. Heater 75,000 BTU Big Maxx heater Quickly and easily converts a Mr. Heater 75,000 BTU Big Maxx heater from natural gas to propane [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Solaria Electric Infrared Heater - Commercial-Grade, Indoor/Outdoor, 3000 Watts, 240 Volts, Model# SALPHAH2-30240S

$529.98

This Solaria commercial-grade Electric Infrared Heater uses advanced short wave infrared heating technology to instantly warm people and objects, not just air, with safe, clean, dependable heat. Primary Heating Application: Commercial, BTU Output: 10,244, Heating Capability (sq. ft.): 200, Volts: 240, Amps: 12.5, Watts: 3,000, Power Cord (ft.): 6, Receptacle Type Required: Hardwire, Dimensions W x D x H (in.): 33 x 5 1 / 2 x 9 Super-efficient operation costs just pennies per hour, converting 92% of consumed energy into comfortable heat Weatherproof casing is safe for use indoors or outdoors Heats instantly with no initial warm up time Modular design allows for easily adjusting heat loads Silent, odorless operation with no risk of combustion Powder-coated aircraft aluminum construction provides rugged durability Wall or ceiling mount design saves space no bulky propane gas containers required [Read more]

Store: Northern Tool and Equipment

Brand: Solaira Heaters

Kats 150 Watt Silicone Pad Heater - Model# 24150

$26.98

Universal pad heater has special 3M adhesive backing to attach to oil pans, hydraulic reservoirs, diesel fuel tanks or any flat metal surface. U.S.A. Primary Heating Application: Vehicle, Volts: 110, Watts: 150, Heat Settings: 1, Thermostat Included: No, Power Cord (ft.): 4, Remote Included: No, Thermal Cutoff Safety Device: No Silicone for outdoor use 3M adhesive backing [Read more]

Store: Northern Tool and Equipment

Brand: Kats Heaters

Solaria Electric Infrared Heater - Commercial-Grade, Indoor/Outdoor, 1500 Watts, 120 Volts, Model# SALPHA15120S

$349.98

This Solaria commercial-grade Electric Infrared Heater uses advanced short wave infrared heating technology to instantly warm people and objects, not just air, with safe, clean, dependable heat. Primary Heating Application: Commercial, BTU Output: 5,122, Heating Capability (sq. ft.): 100, Volts: 120, Amps: 12.5, Watts: 1,500, Power Cord (ft.): 15, Plug Type: NEMA rated 110-120V, Receptacle Type Required: Standard J-box, GFI recommended for wet installations, Dimensions W x D x H (in.): 9 x 5 1 / 2 x 17 Super-efficient operation costs just pennies per hour, converting 92% of consumed energy into comfortable heat Weatherproof casing is safe for use indoors or outdoors Heats instantly with no initial warm up time Modular design allows for easily adjusting heat loads Silent, odorless operation with no risk of combustion Powder-coated aircraft aluminum construction provides rugged durability Wall or ceiling mount design saves space no bulky propane gas containers required UL/CSA approved cord for safety [Read more]

Store: Northern Tool and Equipment

Brand: Solaira Heaters

Mr. Heater Replacement Safety Shutoff Valve With Orifice, Model# 273116

$19.98

Replacement safety shutoff valve for item# 173632. Common Usage: Safety shutoff valve, Works With: Mr. Heater single heater, Includes (qty.): 1 Shutoff valve [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Mr. Heater Portable Propane Forced Air Heater - 250,000 - 400,000 BTU, Model# MH400FAVT

$599.98

Mr. Heater Portable propane heater offers efficient temporary heat for construction sites, agricultural buildings, industrial workspaces, remodeling jobs and more. Features a high-output fan to maximize air circulation, 10-ft. hose and regulator (tank sold separately). High-temperature limit switch/flame safety. Compact and lightweight with attached carrying handle. Includes a built-in thermostat. CSA certified. Vent-Free: No, BTU Output: 400,000, Heating Capability (sq. ft.): 9,000, Primary Heating Application: Construction, garage, Blower Included: Yes, Blower (CFM): 1,400, Blower Power Supply (Volts, Amps): 115, Fuel Type: Propane, Fuel Consumption (gal./hr.): 17 hours on two 100-lb. tanks on low, Igniter: Electronic, Thermostat Included: No, Remote Included: No, Oxygen Depletion Sensor: No, Dimensions W x D x H (in.): 38 1/2 x 14 250,000-400,000 BTU Maximum Heat - Heats up to 9000 sq. ft. Runs A Full Workday - Up to 17 hours on two 100 lb propane cylinder on low setting Safe - Heater shuts off with loss of flame or power supply Minimum required tank size - 200 lb. (sold separately) Instant Heat - Economical, efficient and clean burning Easy Start Ready To Use - Simple Hookup; 10ft. hose and regulator included. Made To Last - Rugged, durable steel construction High Temperature Limit Switch 38 1/2in.W x 14 3/4in.D x 21 3/4in. H [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Mr. Heater Hose Connection For Item# 173634 - 5ft. Length, Model# F273701

$20.98

Connects a 20-lb. propane cylinder to Item# 173634. Works on all cylinders from 5 lbs. to 20 lbs. U.S.A. Common Usage: Hose connection, Works With: Item number 173634, Size: 5ft. Length, Includes: 1 Hose connection [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Mr. Heater Propane Heater - 100,000 BTU, Model# F191925

$599.98

Provides plenty of heat even during power outages requires no electricity. Thermostat is included for comfort control. For indoor use. Recommended for buildings with 19ft. to 22ft. ceilings. AGA design certified. U.S.A. Vent-Free: No, BTU Output: 100,000, Heating Capability (sq. ft.): N/A Radiant heat, Primary Heating Application: Indoor, Fuel Type: Propane, Fuel Consumption (gal./hr.): N/A Thermastatically/Millivolt controlled, Igniter: Electronic, Thermostat Included: Yes 100,000 BTU Efficient infrared heat hirectly heats people and objects which in turn heats surrounding air to desired temperature Economical No electricity required Heats during power outage Convenient Easy to operate and install Quiet, clean, odor-free operation Instant heat Includes adjustable thermostat for individually controlled warmth CSA certified Mounting hardware sold separately [Read more]

Store: Northern Tool and Equipment

Brand: Mr. Heater

Aura Infrared Patio Heater - 1500 Watts, Model# ARMW-2215120S

$179.99

This Aura Infrared Patio Heater uses medium wave infrared technology to deliver safe, odorless and efficient heat indoors or out, with no warm up time. Primary Heating Application: Outdoor, BTU Output: 1,500, Heating Capability (sq. ft.): 86, Volts: 120, Amps: 12.5, Watts: 1,500, Power Cord (ft.): 15, Receptacle Type Required: J box, GFI recommended, Dimensions W x D x H (in.): 22 x 4 x 3 Safe for patios, backyard balconies, terraces, gazebos, garages and screened in rooms Operates on just pennies per hour Long-life tungsten quartz medium wave emitter lasts 5000 hours Weatherproof construction withstands the elements Aircraft-grade anodized aluminum body with stainless steel components provides years of dependable heat [Read more]

Store: Northern Tool and Equipment

Brand: Northern Tool and Equipment

SunStar Heating Products Infrared Ceramic Heater - LP, 100,000 BTU, Model# SG10-L

$699.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Vent-Free: No, BTU Output: 100,000, Heating Capability (sq. ft.): 1,000 - 2,500, Primary Heating Application: Infrared, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Propane, Fuel Consumption (gal./hr.): 1.1, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 33 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 16ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 65in. above, 129in. below and 49in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly requi... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

Optimus Oscillating Tower Ceramic Heater - 1500 Watts, Digital Control, Model# H7328

$69.98

Stylish modern ceramic tower portable heater features electronic thermostat with digital LED temperature display and remote control. Oscillating action spreads heat throughout room. Primary Heating Application: Portable, BTU Output: 5,280, Heating Capability (sq. ft.): 323-538, Volts: 120, Amps: 12.5, Watts: 1,000 & 1,500, Heat Settings: 2, Thermostat Included: Yes, Power Cord (ft.): 6, Plug Type: 2-prong, Receptacle Type Required: Standard, Remote Included: Yes, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: Yes Electronic thermostat with digital LED temperature display Remote control Motorized oscillating base rotates 75 to spread heat evenly through room 1000 and 1500 heat settings Heats up to 538 sq. ft. Space-saving design 4-hour timer Tip-over safety switch Overheat protection circuit with alert light [Read more]

Store: Northern Tool and Equipment

Brand: Optimus

Cadet Electric Baseboard Heater - 240 Volt, 1000 Watt, White, Model# 4F1000W

$39.99

The Cadet 1000 Watt Electric Baseboard Heater is the ideal choice for low-cost installation, while quiet operation and welcome comfort make it the preferred heater for bedrooms, utilizing convection to circulate air. Easy to install for remodel, new construction, or cold room applications. Primary Heating Application: Baseboard, BTU Output: 3,410 / 2,558, Volts: 240 / 208, Amps: 4.17 / 3.61, Watts: 1,000 / 750, Blower Included: No, Heat Settings: 1, Thermostat Included: No, Receptacle Type Required: Hardwire, Thermal Cutoff Safety Device: Oversized high temperature limit switch with full-length capillary sensor tube, Dimensions W x D x H (in.): 48 x 2 1/2 x 6 3/4 1000 Watts @ 240V; 750 Watts @ 208V Size: 48in.W x 2 1/2in.D x 6 3/4in.H Easy installation with pre-punched case at 1in. intervals Powder-coated paint for a smooth, premium finish Rugged steel construction increases durability Works best when placed under a window with 3ft. clearance in front; 12in. above; 6in. to sides Thermostat required (sold separately) [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Ouellet Kickspace Heater - 1000 Watt, 120 Volt, White, Model# OCPU1002BL

$229.99

This compact OCP series fan-forced heater from Ouellet can be recessed in the kickspace under cabinets and is perfect for open concept areas. The 120V motor runs on supplied voltage, eliminating the risk for damage. Two 500 Watt heating elements make it easy to control power outlet as needed. Primary Heating Application: Wall heater, Volts: 120, Amps: 8.34, Watts: 1,000, Blower Included: Yes, Blower (CFM): 80, Heat Settings: No, Thermostat Included: No, Power Cord (ft.): Must be hardwired, Remote Included: No, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 22 x 11 x 4 1/2 Two 500 Watt tubular heating elements (1000 Watt in parallel) High-limit temperature control with auto reset 20-gauge steel construction White powder-coat epoxy/polyester finish Factory lubricated motor [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

Ouellet Portable Heater - 240 Volts, 4000 Watts. Model# OCH4000

$119.98

Designed to provide a back-up heating source at a great price. Great for garage, construction jobsite or workshop. In Almond with durable epoxy/polyester powder paint. Primary Heating Application: Construction, garage, BTU Output: 13,648, Volts: 240, Amps: 16.67, Watts: 4,000, Blower Included: Yes, Blower (CFM): 300, Heat Settings: Adjustable, Thermostat Included: Yes, Power Cord (ft.): 6, Plug Type: 3 prong plug, Receptacle Type Required: Grounded 3 pronged 20 amp, 250vac, 240 volt outlet, Remote Included: No, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 13 x 10 x 13 240V, single-phase 20 Amp, 250VAC grounded 3-prong plug Handle may be used as a reel for electric cord 6ft. electric cord High-limit temperature control with automatic reset Fan delivers 300 CFM Steel tubular heating element Built-in thermostat, 60-170 F [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

TPI Portable Electric Heater - 13,652 BTU, Model# 474-TM

$134.99

This TPI Portable Electric Heater goes anywhere to add 13,652 BTU of warmth to rooms up to 200 square feet. Built in bi-metal thermostat lets you adjust temperature from 50-90. 262 CFM. 10ft. air throw. U.S.A. Primary Heating Application: Portable, BTU Output: 13,652, Heating Capability (sq. ft.): 200, Volts: 240 single phase, Amps: 12.5, Watts: 2,000 / 4,000, Blower Included: Yes, Blower (CFM): 262, Heat Settings: Thermostat, Thermostat Included: Yes, Power Cord (ft.): 6, Plug Type: 20A NEMA #6-20P, Receptacle Type Required: 20A NEMA #6-20P, Remote Included: No, Dimensions W x D x H (in.): 16 x 8 1/2 x 16 Goes anywhere to add 13,652 BTU of warmth to rooms up to 200 square feet Adjust temperature from 50-90 262 CFM 10ft. air throw [Read more]

Store: Northern Tool and Equipment

Brand: TPI

SunStar Heating Products Infrared Ceramic Heater - NG, 26,000 BTU, Model# SGM3-N1

$359.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended in windy or drafty environments). This is a Millivolt Standing Pilot heater and does not require an external power or electricity to operate, so its great for use during power outages. Requires Millivolt thermostat for SGM (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Primary Heating Application: Infrared, Vent-Free: No, BTU Output: 26,000, Heating Capability (sq. ft.): 500, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 0.3, Gas Inlet (in.): 1/2, Igniter: Standing millivolt pilot, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 29 x 22 x 12 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant output Heaters can be angle mounted horizontally and up to 45 degrees The minimum mounting height is 12ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 24in. above, 48in. below and 24in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure reg... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - NG, 52,000 BTU, Model# SGM6-N1A

$399.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is a Millivolt Standing Pilot heater and does not require an external power or electricity to operate, so its great for use during power outages. Requires a 750 Millivolt Thermostat to operate (sold separately). Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Primary Heating Application: Infrared, Vent-Free: No, BTU Output: 52,000, Heating Capability (sq. ft.): 500 - 1,500, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 0.6, Gas Inlet (in.): 1/2, Igniter: Standing millivolt pilot, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 40 x 22 x 12 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant output Heaters can be angle mounted horizontally and up to 45 degrees The minimum mounting height is 14ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 36in. above, 72in. below and 36in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) Supply pressure of 7in. WC is critical and supply pressure less than 7in. WC can affect the operation of the pilot/heater The standing pilot flame can be affected in windy/dra... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

Cadet ComPak Twin Plus Electric In-Wall Heater - 240V, 3000 Watt, White, Model# CSTC302TW

$189.99

The Cadet ComPak Twin Plus In-Wall fan-forced heater is perfect for heating large areas such as an open foyer with a single heater. The Model CSTC302TW is connected behind a single grill, providing all the benefits of the ComPak Plus. Thermostat included. Quietly provides instant warmth and comfort to a larger area. Primary Heating Application: Wall heater, BTU Output: 10,230 / 7,672, Volts: 240 / 208, Amps: 12.5 / 10.82, Watts: 3,000 / 2,250, Blower Included: Yes, Heat Settings: 1, Thermostat Included: Yes, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: Dual primary and secondary thermal safeguards, Dimensions W x D x H (in.): 16 1/4 x 4 x 12 3000 Watts @ 240V; 2250 Watts @ 208V Rough-in dimensions: 14 5/8in.W x 4in.D x 10in.H Two Nichrome coil element for quick heat Two quiet, 2-stage centrifugal blowers Powder-coated wall can eliminates sharp edges Premium-finish white grill Clearance: 3ft. in front, 12in. above, 6in. to sides [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Soleus Oscillating Reflective Heater - 800 Watts, Model# HR3-08-21

$44.99

This Soleus Oscillating Reflective Heater provides instant, comfy warmth by heating objects, not the air. In addition, this energy-efficient heater is silent, odorless and does not burn oxygen or dust. Primary Heating Application: Portable, Volts: 120, Amps: 6.7, Watts: 800, Heat Settings: 3, Power Cord (ft.): 5.9, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: Yes, Dimensions W x D x H (in.): 11 x 8 x 21 1/4 Low temperature surface provides extra measure of safety [Read more]

Store: Northern Tool and Equipment

Brand: Soleus

SunStar Heating Products Infrared Ceramic Heater - NG, 120,000 BTU, Model# SG12-N

$499.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc) prior to purchasing the heater. Primary Heating Application: Infrared, Vent-Free: No, BTU Output: 120,000, Heating Capability (sq. ft.): 1,000 - 3,000, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 1.2, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 33 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angled mounted horizontal and up to 30 degrees The minimum mounting height is 16ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 65in. above, 129in. below and 49in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly req... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - NG, 30,000 BTU, Model# SG3-N

$339.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Primary Heating Application: Infrared, Vent-Free: No, BTU Output: 30,000, Heating Capability (sq. ft.): 500 - 1,500, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 0.3, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 23 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 12ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 37in. above, 73in. below and 31in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly requi... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - LP, 26,000 BTU, Model# SGM3-L1

$359.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is a Millivolt Standing Pilot heater and does not require an external power or electricity to operate, so its great for use during power outages. Requires a 750 Millivolt Thermostat to operate (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Vent-Free: No, BTU Output: 26,000, Heating Capability (sq. ft.): 500 -750, Primary Heating Application: Infrared, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Propane, Fuel Consumption (gal./hr.): 0.3, Gas Inlet (in.): 1/2, Igniter: Standing millivolt pilot, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 29 x 22 x 12 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant output Heaters can be angle mounted horizontally and up to 45 degrees The minimum mounting height is 12ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 24in. above, 48in. below and 24in. from the sides of the heater The minimum supply gas pressure is 11.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regula... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

Ouellet Radiant Heater - 1500 Watt, 120 Volt, Model# ORR1502

$399.98

This ORR series radiant heater from Ouellet is designed to heat specific areas within large spaces. These low-inertia heaters are able to make an area comfortable in minutes. An anodized aluminum reflector allows maximum heat distribution. Great for warehouses, workshops, indoor swimming pools and churches. Primary Heating Application: Construction, garage, Volts: 120, Amps: 12.5, Watts: 1,500, Heat Settings: No, Thermostat Included: No, Power Cord (ft.): Must be hardwired, Remote Included: No, Thermal Cutoff Safety Device: No, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 45 x 6 x 8 Built-in adjustable directional system 60 standard radiation angle Incoloy stainless steel tubular heating element No visible light emitted by heater Vertical or horizontal mounting Surface mounted or suspended by chains 43 1/2in. overall length 32in. long heating element 8ft. to 10ft. recommended installation height [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

Indus-Tool Hi-Lo Switch for Electric Floor/Desk Heaters

$13.98

Switch lets you adjust heat levels of Heated Floor Mats, Item#s 331663, 331664 and 331665. On/off switch can be positioned for easy access where you stand or sit. U.S.A. [Read more]

Store: Northern Tool and Equipment

Brand: Indus-Tool

Cadet Electric Baseboard Heater - 240 Volt, 750 Watt, White, Model# 3F750W

$39.99

The Cadet 750 Watt Electric Baseboard Heater is the ideal choice for low-cost installation, while quiet operation and welcome comfort make it the preferred heater for bedrooms, utilizing convection to circulate air. Easy to install for remodel, new construction, or cold room applications. Primary Heating Application: Baseboard, BTU Output: 25,579 / 1,920, Volts: 240 / 208, Amps: 3.13 / 2.71, Watts: 750 / 563, Blower Included: No, Heat Settings: 1, Thermostat Included: No, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: Oversized high temperature limit switch with full-length capillary sensor tube, Dimensions W x D x H (in.): 36 x 2 1/2 x 6 3/4 750 Watts @ 240V; 563 Watts @ 208V Size: 36in.W x 2 1/2in.D x 6 3/4in.H Easy installation with pre-punched case at 1in. intervals Powder-coated paint for a smooth, premium finish Rugged steel construction increases durability Works best when placed under a window with 3ft. clearance in front; 12in. above; 6in. to sides Thermostat required (sold separately) [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Cadet Electric Baseboard Heater - 240 Volt, 1250 Watt, White, Model# 5F1250W

$49.99

The Cadet 1250 Watt Electric Baseboard Heater is the ideal choice for low-cost installation, while quiet operation and welcome comfort make it the preferred heater for bedrooms, utilizing convection to circulate air. Easy to install for remodel, new construction, or cold room applications. Primary Heating Application: Baseboard, BTU Output: 4,263 / 3,195, Volts: 240 / 208, Amps: 5.21 / 4.5, Watts: 1,250 / 937, Blower Included: No, Heat Settings: 1, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: Oversized high temperature limit switch with full-length capillary sensor tube, Dimensions W x D x H (in.): 60 x 2 1/2 x 6 3/4 1250 Watts @ 240V; 937 Watts @ 208V Size: 60in.W x 2 1/2in.D x 6 3/4in.H Easy installation with pre-punched case at 1in. intervals Powder-coated paint for a smooth, premium finish Rugged steel construction increases durability Works best when placed under a window with 3ft. clearance in front; 12in. above; 6in. to sides Thermostat required (sold separately) [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Cadet Electric Baseboard Heater - 240 Volt, 500 Watt, White, Model# 2F500W

$29.98

The Cadet 500 Watt Electric Baseboard Heater is the ideal choice for low-cost installation, while quiet operation and welcome comfort make it the preferred heater for bedrooms, utilizing convection to circulate air. Easy to install for remodel, new construction, or cold room applications. Primary Heating Application: Baseboard, BTU Output: 1,705 / 1,279, Volts: 240 / 208, Amps: 2.08 / 1.8, Watts: 500 / 375, Blower Included: No, Heat Settings: 1, Thermostat Included: No, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: Oversized high temperature limit switch with full-length capillary sensor tube, Dimensions W x D x H (in.): 30 x 2 1/2 x 6 3/4 500 Watts @ 240V; 375 Watts @ 208V Size: 30in.W x 2 1/2in.D x 6 3/4in.H Easy installation with pre-punched case at 1in. intervals Powder-coated paint for a smooth, premium finish Rugged steel construction increases durability Works best when placed under a window with 3ft. clearance in front; 12in. above; 6in. to sides Thermostat required (sold separately) [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Cadet ComPak Twin Plus Electric In-Wall Heater - 240V, 4000 Watt, White, Model# CSTC402TW

$199.99

The Cadet ComPak Twin Plus In-Wall fan-forced heater is perfect for heating large areas such as an open foyer with a single heater. The Model CSTC402TW is connected behind a single grill, providing all the benefits of the ComPak Plus. Thermostat included. Quietly provides instant warmth and comfort to a larger area. Primary Heating Application: Wall heater, BTU Output: 13,640 / 10,230, Volts: 240 / 208, Amps: 16.67 / 14.42, Watts: 4,000 / 3,000, Blower Included: Yes, Heat Settings: 1, Thermostat Included: Yes, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: Two oversized 16 Amp rating manual power reset @ 240V, with two over-temperature thermal back-up fuse, Dimensions W x D x H (in.): 16 1/4 x 4 x 12 4000 Watts @ 240V; 3000 Watts @ 208V Rough-in dimensions: 14 5/8in.W x 4in.D x 10in.H Two Nichrome coil element for quick heat Quiet, 2-stage centrifugal blower Dual primary and secondary thermal safeguards Powder-coated wall can eliminates sharp edges Premium-finish white grill Clearance: 3ft. in front, 12in. above, 6in. to sides [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

CZ Infrared Blue Edition Therapeutic Quartz Infrared Portable Heater/Air Purifier, Model# CZI-1500-PA

$399.98

The CZ Infrared Blue Edition Therapeutic Quartz Infrared Portable Heater is 35% more efficient than other infrared heaters on the market. The CZI-1500-PA features the Bio-Smart patented 5-stage air purification system, dual power settings (1500 & 750 Watt) and an ultraquiet dual speed fan system. Primary Heating Application: Infrared, BTU Output: 6,800, Heating Capability (sq. ft.): 1,000, Volts: 115, Amps: 12.6, Watts: 1,500 / 750, Blower Included: Yes, Heat Settings: Digital range thermostat with High/Low Watt settings, Thermostat Included: Yes, Power Cord (ft.): 6, Receptacle Type Required: Conventional 110V 3-prong grounded outlet, Remote Included: Yes, Thermal Cutoff Safety Device: Yes, Dimensions W x D x H (in.): 13.5 x 16.5 x 14 Longer, heftier, more powerful heating elements now lasting 30,000 hours 115 Volts rather than industry standard 60 Volts (more volts = more efficiency) Accurate digital thermostatic controls Heating element filament now twice the density Improved patent-pending ceramic terminals for greater durability and longevity Copper fins in the heating chamber replace metal diffusion coil for 10% more efficiency and less noise 3 large copper panels instead of two Temperature at the grill is 204-214 (previously 160 ) Internal temperature is 266 (previously 240 ) Bio-Smart 5-stage air purification system eliminates airborne bacteria, pathogens, VOCs, smoke and toxic fumes Washable prefilter Plastic cabinet with faux wood trim Caster wheels [Read more]

Store: Northern Tool and Equipment

Brand: CZ Infrared

Cadet Electric Baseboard Heater - 120 Volt, 1000 Watt, White, Model# 4F1000W-1W

$39.99

The Cadet 1000 Watt Electric Baseboard Heater is the ideal choice for low-cost installation, while quiet operation and welcome comfort make it the preferred heater for bedrooms, utilizing convection to circulate air. Easy to install for remodel, new construction, or cold room applications. Primary Heating Application: Baseboard, BTU Output: 3,410, Volts: 120, Amps: 8.33, Watts: 1,000, Blower Included: No, Heat Settings: 1, Thermostat Included: No, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: Oversized high temperature limit switch with full-length capillary sensor tube, Dimensions W x D x H (in.): 48 x 2 1/2 x 6 3/4 1000 Watts, 120 Volt Size: 48in.W x 2 1/2in.D x 6 3/4in.H Easy installation with pre-punched case at 1in. intervals Powder-coated paint for a smooth, premium finish Rugged steel construction increases durability Works best when placed under a window with 3ft. clearance in front; 12in. above; 6in. to sides Thermostat required (sold separately) [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

SunStar Heating Products Infrared Ceramic Heater - NG, 40,000 BTU, Model# SG4-N

$599.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Primary Heating Application: Infrared, Vent-Free: No, BTU Output: 40,000, Heating Capability (sq. ft.): 500 - 15,000, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 0.3, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 23 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 12ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 37in. above, 73in. below and 31in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly requ... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

Aloha 1350 Watt Quartz Radiant Heater, Model# 06080

$49.99

The Aloha 1350 Watt quartz radiant heater delivers powerful halogen heat while the built-in fan distributes warmth throughout the room. Boasts several safety features. Thermostat is adjustable. Primary Heating Application: Radiant, Watts: 1,350, Blower Included: No, Heat Settings: 2, Thermostat Included: Yes, Remote Included: No, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: Yes Warning light and buzzer Safe-Techtive grill [Read more]

Store: Northern Tool and Equipment

Brand: Aloha Breeze

SunStar Heating Products Infrared Ceramic Heater - NG, 100,000 BTU, Model# SG10-N

$499.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Primary Heating Application: Infrared, Vent-Free: No, BTU Output: 100,000, Heating Capability (sq. ft.): 1,000 - 3,000, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 1, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 33 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 15ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 65in. above, 129in. below and 49in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly req... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - NG, 80,000 BTU, Model# SG8-N

$399.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Vent-Free: No, BTU Output: 80,000, Heating Capability (sq. ft.): 1,000 - 3,000, Primary Heating Application: Infrared, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 1, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 28 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 14ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 49in. above, 99in. below and 49in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly requi... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - NG, 104,000 BTU, Model# SGM10-N1A

$549.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is a Millivolt Standing Pilot heater and does not require an external power or electricity to operate, so its great for use during power outages. Requires Millivolt thermostat for SGM (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Primary Heating Application: Infrared, Vent-Free: No, BTU Output: 104,000, Heating Capability (sq. ft.): 500 - 2,000, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 1, Gas Inlet (in.): 1/2, Igniter: Standing millivolt pilot, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 61 x 22 x 12 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant output Heaters can be angle mounted horizontally and up to 45 degrees The minimum mounting height is 15ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 36in. above, 96in. below and 45in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 7in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - NG, 155,000 BTU, Model# SG15-N

$599.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Primary Heating Application: Infrared, Vent-Free: No, BTU Output: 155,000, Heating Capability (sq. ft.): 1,000 - 5,000, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 1.6, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 38 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 18ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 65in. above, 137in. below and 49in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly r... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - LP, 65,000 BTU, Model# SG6-L

$399.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc) prior to purchasing the heater. Vent-Free: No, BTU Output: 65,000, Heating Capability (sq. ft.): 750 - 2,500, Primary Heating Application: Infrared, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Propane, Fuel Consumption (gal./hr.): 0.6, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 28 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally up to 30 degrees The minimum mounting height is 13ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 49in. above, 99in. below and 49in. from the sides of the heater The minimum supply gas pressure is 11.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly required Heat... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - NG, 140,000 BTU, Model# SG14-N

$599.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). Indoor use only. May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc) prior to purchasing the heater. Vent-Free: No, BTU Output: 104,000, Primary Heating Application: Infrared, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 1.1 (used continuously), Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 38 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 17ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 65in. above, 137in. below and 49in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly required Heaters are 100% test-fired prior to sh... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - NG, 60,000 BTU, Model# SG6-N

$399.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Primary Heating Application: Infrared, Vent-Free: No, BTU Output: 60,000, Heating Capability (sq. ft.): 750 - 2,500, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Natural Gas, Fuel Consumption (gal./hr.): 0.6, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 28 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 13ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 49in. above, 99in. below and 49in. from the sides of the heater The minimum supply gas pressure is 7.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly requi... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products 750 Millivolt Thermostat for SGM Series Infrared Ceramic Heaters, Model# 42489010

$24.98

Universal-mount 750 Millivolt Thermostat is required for SGM Series Infrared Ceramic Heaters. Includes 20ft. wire and faceplates. U.S.A. Compatible With: SGM Series Infrared Ceramic Heaters, Thermostate Range ( F): 50 - 90, Mounting Type: Wall mount, LED Light: No, Includes: 20ft. wire and faceplates Snap-action operation makes precise leveling unnecessary [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - LP, 52,000 BTU, Model# SGM6-L1

$399.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for windy/drafty environments). This is a Millivolt Standing Pilot heater and does not require an external power or electricity to operate, so its great for use during power outages. Requires a 750 Millivolt Thermostat to operate (sold separately). Indoor use only. May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Vent-Free: No, BTU Output: 52,000, Heating Capability (sq. ft.): 500 - 1,500, Primary Heating Application: Infrared, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Propane, Fuel Consumption (gal./hr.): 0.57, Gas Inlet (in.): 1/2, Igniter: Standing millivolt pilot, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 40 x 22 x 12 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant output Heaters can be angle mounted horizontally and up to 45 degrees The minimum mounting height is 14ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 36in. above, 72in. below and 36in. from the sides of the heater The minimum supply gas pressure is 11.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a l... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

Cadet Garage/Utility Heater - 4000 Watts, 240 Volts, Model# CGH402

$199.99

This portable Cadet Garage/Utility Heater provides plenty of comfortable warmth for difficult-to-heat areas in garages and workshops whether on the floor or mounted to the wall or ceiling. Primary Heating Application: Construction, garage, BTU Output: 13,652 / 10,240, Heating Capability (sq. ft.): 500, Volts: 240 / 208, Amps: 16.7 @ 240V / 14.4 @ 208V, Watts: 4,000 @ 240V / 3,000 @ 208V, Blower Included: Yes, Power Cord (ft.): 6, Plug Type: 20 Amp, Receptacle Type Required: 240V NEMA #6-20, Remote Included: No, Thermal Cutoff Safety Device: Manual reset, Dimensions W x D x H (in.): 13 3/4 x 10 1/2 x 15 3/4 Portable design for versatility Bracket for floor or wall/ceiling use Open airflow reduces debris buildup Thermal safeguard with high temperature manual reset turns heater off if normal operating temperatures are exceeded Finned steel tubular heating element Built-in single pole thermostat with mechanical off Requires 20 Amp, 240 Volt receptacle [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Ouellet Radiant Heater - 2000 Watt, 240 Volt, Model# ORR2000

$369.98

This ORR series radiant heater from Ouellet is designed to heat specific areas within large spaces. These low-inertia heaters are able to make an area comfortable in minutes. An anodized aluminum reflector allows maximum heat distribution. Great for warehouses, workshops, indoor swimming pools and churches Primary Heating Application: Radiant, Volts: 240, Amps: 8.34, Watts: 2,000, Heat Settings: No, Thermostat Included: No, Power Cord (ft.): Must be hardwired, Remote Included: No, Thermal Cutoff Safety Device: No, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 45 x 6 x 8 Built-in adjustable directional system 60 standard radiation angle Incoloy stainless steel tubular heating element No visible light emitted by heater Vertical or horizontal mounting Surface mounted or suspended by chains 43 1/2in. overall length 32in. long heating element 8ft. to 10ft. recommended installation height [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

SunStar Heating Products Infrared Ceramic Heater - LP, 130,000 BTU, Model# SG13-L

$599.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc) prior to purchasing the heater. Vent-Free: No, BTU Output: 130,00, Heating Capability (sq. ft.): 1,000 - 3,000, Primary Heating Application: Infrared, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Propane, Fuel Consumption (gal./hr.): 1.3, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 38 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 17ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 65in. above, 137in. below and 49in. from the sides of the heater The minimum supply gas pressure is 11.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly requir... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

SunStar Heating Products Infrared Ceramic Heater - LP, 32,000 BTU, Model# SG3-L

$599.98

The SunStar Heating Products Ceramic Heater is ideal for spot heating or area heating of remote locations, farm buildings, shops, service areas, pump houses or other hard-to-heat spaces, providing both fuel efficiency of radiant heat and installation flexibility (not recommended for car washes). This is an energy-saving Direct Spark Ignition heater and can be controlled by a line voltage or 24V thermostat (sold separately). May require the following second stage regulators prior to the heater based on gas supply pressure: A regulator up to 2 PSIG line pressure or a regulator above 2 PSIG line pressure (both sold separately). NOT CERTIFIED OR APPROVED FOR RESIDENTIAL USE. Indoor use only. U.S.A. NOTE: Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Vent-Free: No, BTU Output: 32,000, Heating Capability (sq. ft.): 750 - 1,500, Primary Heating Application: Infrared, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Propane, Fuel Consumption (gal./hr.): 0.3, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 23 x 31 x 11 Constructed from aluminized steel for corrosion resistance and long life Aluminum reflectors are designed to maximize radiant efficiency Heaters can be angle mounted horizontally and up to 30 degrees The minimum mounting height is 12ft. above finished floor for uniform energy distribution and human comfort Requires the following clearances from any combustible material: 37in. above, 73in. below and 31in. from the sides of the heater The minimum supply gas pressure is 11.0in. Water Column (WC) and the maximum supply pressure is 14in. WC gas pressure If higher gas pressure is supplied, you will need to install a line pressure regulator (sold separately) to reduce it to less than 14in. WC (or 1/2 PSIG) No assembly required... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

TPI Portable Infrared Heater - 20,478 BTU, 6.0kW, 240 Volts, Model# FHK-624-3A

$499.98

With this TPI Portable Infrared Heater, you can wheel instant, focused heat exactly where you need it. Gold-anodized internal reflector maximizes efficiency and provides 60 symmetrical heating pattern to heat objects, not just air. Double-side wall housing and a top baffle reduce operating temperatures and lower the risk of fire. Durable 5000-hour rated infrared heating elements. U.S.A. Primary Heating Application: Construction, garage, BTU Output: 20,478, Volts: 240, Watts: 6.0kw, Dimensions W x D x H (in.): 15 x 36 x 18 Gold-anodized internal reflector maximizes efficiency and provides 60 symmetrical heating pattern to heat objects, not just air Double-side wall housing and a top baffle reduce operating temperatures and lower the risk of fire Durable 5000-hour rated infrared heating elements [Read more]

Store: Northern Tool and Equipment

Brand: TPI

UFO Indoor/Outdoor Infrared Electric Wall Mount Heater - 1500 Watts, Model# UFO S-15

$299.98

This UFO Indoor/Outdoor Infrared Electric Wall Mount Heater provides faster heat and bigger savings. Mid-wave infrared technology delivers soothing heat in just seconds heats objects, not air. Energy smart for the environment, 94% of energy consumed is converted into heat, not affected by wind or air movements. Adjust the temperature for optimum indoor or outdoor comfort. Special easy-touch grill for safety and longest available heating filament life. Safe, odorless heat. Fully weatherproof. Includes wall mount. (Optional floor stand sold separately, Item#686703). 2-year full replacement warranty. Primary Heating Application: Infrared, Heating Capability (sq. ft.): 54-109 outdoors; 161 indoors, Volts: 110, Amps: 13.6 @ 1 phase/4.5 @ 3 phase, Watts: 1500, Thermostat Included: Adjustable, Power Cord (ft.): 8, Plug Type: NEMA plug 5-15p, Remote Included: No, Tip-Over Safety Switch: Yes Mid-wave infrared technology delivers soothing heat in just seconds heats objects, not air Converts 94% of energy consumed into heat Adjustable temperature Longest available heating filament life Safe, odorless heat Fully weatherproof [Read more]

Store: Northern Tool and Equipment

Brand: Ufo

Ouellet Residential Radiant Cove Heater - 120 Volts, 1-Phase, 1200 Watts, Model# ORC1202BL

$179.99

Small residential and light commercial heater that you can install on the wall to heat where space limitations wont allow you to install a conventional heater. Great for use in nursery, laundry room, bathroom or workshop. In White. Primary Heating Application: Radiant, Volts: 120, Amps: 10, Watts: 1,200, Heat Settings: No, Thermostat Included: No, Power Cord (ft.): Must be hardwired, Remote Included: No, Thermal Cutoff Safety Device: No, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 96 x 4 x 7 120 Volts, single-phase Front made of aluminum extrusion profiled to increase radiating surface Back of unit made with 18-gauge painted steel Large junction box on each end with connector for quick installation Wall installation bracket doesnt require opening units housing Stainless steel tubular heating element inserted into a solid aluminum extrusion preventing any thermal expansion noise 6ft. minimum clearance to floor; 4 1/2in. minimum to ceiling [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

Lanair Waste Oil-Fired Thermostat-Controlled Heater Package - 150,000 BTU, 5000 SQ. FT. Capacity, Thru-Wall Chimney, Model# MX-150 Package D

$5,099.99

Energy costs are on the rise Take control with a waste oil fired heater package from Lanair. Waste oil not only eliminates the cost to haul used oil off-site, but it can reduce your heating bills too. In addition, burning waste oil to get free heat deals with a major pollution problem in an environmentally friendly way. Complete package is designed for commercial use. Advanced atomization technology with monthly maintenance eliminates the tedious daily cleaning required by old vaporization technology. Heat output varies with fuel type, building design, placement and heat loss. This item is not for sale in the state of California. Customers are responsible for checking local codes and regulations prior to purchase. BTU Output: 150,000, Heating Capability (sq. ft.): 5,000, Volts: 120, Amps: 19.5, Blower (CFM): 2,400, Fuel Capacity (gal.): 215, Fuel Type: Waste Oil, Fuel Consumption (gal./hr.): 1.07, Thermostat Included: Yes, Chimney Pipe Size (in.): 6, Chimney Type: Through-wall, Dimensions L x W x H (in.): 48 x 40 x 24 MX-150 heater Pump, filter, fuel piping kit, fuel lines, fittings, and burner Rust-resistant galvanized cabinet Adjustable locking louvers Axial fan Chimney pipe: Class A kit for 16ft. eave through-wall Chimney location: Top/left side AC power: 60Hz. Compressed air (customer supplied) : 2 CFM, 15 PSI Combustion chamber: 12 GA CRS Hanging weight (lbs.): 413 UL listed [Read more]

Store: Northern Tool and Equipment

Brand: Lanair

TPI Suspended Salamander Heater - 102,390 BTU, 480 Volt, Model# YES-3048-3A

$1,299.98

This TPI Suspended Salamander Heater hangs from walls or ceilings of garages, workshops or any place a constant temperature is desired. U.S.A. Primary Heating Application: Construction, garage, BTU Output: 102,390, Heating Capability (sq. ft.): 3,000, Volts: 480, 3-phase, Amps: 36, Watts: 30kw, Blower Included: Yes, Blower (CFM): 1,100, Heat Settings: Thermostat, Thermostat Included: Yes, Plug Type: Hard wire, Remote Included: No, Thermal Cutoff Safety Device: Yes, Dimensions W x D x H (in.): 24 x 24 x 36 Made of 20-gauge steel with front and rear wire mesh guards Powder coated in safety yellow Magnetic switch allows for fan only operation Includes blower, thermostat, thermal cutoff safety device and mounting hardware For indoor use only [Read more]

Store: Northern Tool and Equipment

Brand: TPI

TPI Suspended Salamander Heater - 51,195 BTU, 208 Volt, Model# YES-1520-3A

$799.98

This TPI Suspended Salamander Heater hangs from walls or ceilings of garages, workshops or any place a constant temperature is desired. U.S.A. Primary Heating Application: Construction, garage, BTU Output: 51,195, Heating Capability (sq. ft.): 2,000, Volts: 208, 3-phase, Amps: 42, Watts: 15.0kW, Blower Included: Yes, Blower (CFM): 800, Heat Settings: Thermostat controlled, Thermostat Included: Yes, Power Cord (ft.): Hard wire, Remote Included: No, Thermal Cutoff Safety Device: Yes, Dimensions W x D x H (in.): 24 x 24 x 36 Made of 20-gauge steel with front and rear wire mesh guards Powder coated in safety yellow Magnetic switch allows for fan only operation Includes blower, thermostat, thermal cutoff safety device and mounting hardware For indoor use only [Read more]

Store: Northern Tool and Equipment

Brand: TPI

Soleus Portable Air Conditioner with 12,500 BTU Heater - 13,000 BTU, 225 CFM, Model# PH5-13R-35D

$629.98

The Soleus Portable Air Conditioner is a multi-season unit that takes the place of several appliances, saving space and energy. Evaporative technology reduces the need to drain condensate. Designed to efficiently cool, dehumidify, or heat any space without permanent installation. Heavy-duty casters allow the unit to be easily rolled almost anywhere. Application: Air conditioner, BTU Cooling: 13,000, BTU Heating: 12,000, Capacity: 60 Pints per day, Volts: 115, CFM: 225, Dimensions L x W x H (in.): 18 7/8 x 17 1/8 x 32, Speeds (qty.): 3, Temperature Range ( F): 64 - 90, Timer: Yes, Watts: 1,350 R-410A refrigerant for increased efficiency and reliability Evaporative technology for hassle-free moisture removal Motorized pump system for fast moisture removal 24 hour programmable timer Sleep mode for energy savings Smart chip technology memorizes settings LED display. Loss of power protection w/auto restart Dual hose exhaust system Washable and reusable filter [Read more]

Store: Northern Tool and Equipment

Brand: Soleus

Ouellet Cabinet Heater - 10 kW, Includes Thermostat, Model# OCAU10034CR48TAM

$1,999.98

This versatile Ouellet cabinet heater be recessed in a wall or ceiling or mounted on the floor, wall or ceiling as needed. Flexible installation and a formidable heating ability make this heater beneficial no matter where it is installed. Primary Heating Application: Wall heater, Volts: 480 3 Phase, Blower Included: Yes, Thermostat Included: Yes, Receptacle Type Required: Must be hardwired 10 kW, 480V, 3-phase cabinet heater Fans powered by two-speed motors with permanently lubricated sleeve bearings, increasing reliability Blower wheel is mounted directly on the motor shaft, reducing noise level No belts or bearing blocks required for blowers [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

Lanair Waste Oil-Fired Thermostat-Controlled Heater Package - 150,000 BTU, 5000 SQ. FT. Capacity, Thru-Roof Chimney, Model# MX-150 Package C

$4,999.99

Energy costs are on the rise Take control with a waste oil fired heater package from Lanair. Waste oil not only eliminates the cost to haul used oil off-site, but it can reduce your heating bills too. In addition, burning waste oil to get free heat deals with a major pollution problem in an environmentally friendly way. Complete package is designed for commercial use only. Advanced atomization technology with monthly maintenance eliminates the tedious daily cleaning required by old vaporization technology. Heat output varies with fuel type, building design, placement and heat loss. U.S.A. This item is not for sale in the state of California. Customers are responsible for checking local codes and regulations prior to purchase. BTU Output: 150,000, Heating Capability (sq. ft.): 5,000, Volts: 120, Amps: 19.5, Blower (CFM): 2,400, Fuel Capacity (gal.): 215, Fuel Type: Waste Oil, Fuel Consumption (gal./hr.): 1.07, Thermostat Included: Yes, Chimney Pipe Size (in.): 6, Chimney Type: Through-roof, Dimensions L x W x H (in.): 48 x 40 x 24 MX-150 heater Pump, filter, fuel piping kit, fuel lines, fittings, and burner Rust-resistant galvanized cabinet Adjustable locking louvers Axial fan 2400 CFM Chimney pipe: Class A kit for 16ft. eave through-roof Chimney location: Top/left side AC power: 120V, 60Hz. Compressed air (customer supplied) : 2 CFM, 15 PSI Combustion chamber: 12 GA CRS Hanging weight (lbs.): 413 UL listed [Read more]

Store: Northern Tool and Equipment

Brand: Lanair

TPI Indoor/Outdoor Quartz Infrared Heater - 10,922 BTU, 240 Volts, Galvanized Steel, Model# 222-90-TH-240V

$359.98

This TPI Indoor/Outdoor Quartz Infrared Heater offers the same powerful heat as the heaters used at bus stops. Industrial-grade quartz infrared heater instantly delivers generous amounts of heat when you need it and cools down fast when you dont. Rugged 20-gauge steel withstands years of use, indoors or outdoors great for sheds, barns, workshops, outdoor work areas and more. Gold anodized aluminum reflectors and porcelain end caps provide 97% efficient reflectivity, broadcasting a wide 90 pattern. Resistant to moisture and thermal shock. Coiled tungsten filament in a sealed halogen-filled quartz envelope. 6in. wire pigtail leads. In galvanized with baked-on brown enamel finish. ETL listed housing. Requires hardwired connection. U.S.A. Primary Heating Application: Outdoor overhead and indoor industrial heating, BTU Output: 10,922, Volts: 240, Watts: 3.2kw, Blower Included: No, Thermostat Included: No, Plug Type: Hardwire, Dimensions W x D x H (in.): 15 x 24 x 11 Same powerful heat as the heaters used at bus stops Instantly delivers heat when you need it and cools down fast when you dont Rugged 20-gauge steel withstands years of use, indoors or outdoors Gold anodized aluminum reflectors and porcelain end caps provide 97% efficient reflectivity, broadcasting a wide 90 pattern Resistant to moisture and thermal shock Coiled tungsten filament in a sealed halogen-filled quartz envelope Galvanized steel with baked-on brown enamel finish [Read more]

Store: Northern Tool and Equipment

Brand: TPI

Ouellet Electric Baseboard Heater - 750 Watt, Almond, Model# OFM0752AM

$44.99

The Ouellet 750 Watt Electric Baseboard Heater provides a compact design that delivers high performance and strength while easing installation. Primary Heating Application: Baseboard, Volts: 120, Watts: 750, Blower Included: No, Thermostat Included: No, Power Cord (ft.): Must be hardwired, Remote Included: No, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: No Steel tubular heating element with aluminum fins Linear high-limit temperature control with automatic reset Compact design delivers high performance and strength Does not require use of a furring strip during installation Features sturdy 22-gauge steel body with 20-gauge front panel Almond epoxy/polyester powder-coat paint May be repainted with any interior paint Optional thermostat kit can be installed at either end [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

Cadet Compak Plus Heater - Box Only with Thermostat, 240 Volt, 2000 Watt, Model# CS202T

$99.98

The Cadet ComPak Plus In-Wall fan-forced heater is perfect for smaller areas or larger areas needing the dispersed heat created by multiple heaters. This ComPak Plus heater takes up less space than baseboards or larger in-wall heaters with its unique, compact design. Quietly provides instant warmth and comfort to a cold room. Primary Heating Application: Wall heater, BTU Output: 6,820 / 5,115, Volts: 240 / 208, Amps: 8.33 / 7.21, Watts: 2,000 / 1,500, Blower Included: Yes, Heat Settings: 1, Thermostat Included: Yes, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: Primary 16 Amp rating manual power reset @ 240V, with over-temperature thermal back-up fuse, Dimensions W x D x H (in.): 7 7/8 x 4 x 11 1/2 Heater assembly with thermostat only; wall can and grill sold separately 2000 Watts @ 240V; 1500 Watts @ 208V Nichrome coil element for quick heat Quiet, 2-stage centrifugal blower Primary and secondary thermal safeguards Replaces C or CS series in-wall heaters Clearance: 3ft. in front, 12in. above, 6in. to sides [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Cadet Register Plus Heater - 240 Volts, 2000 Watts, Model# RM202W

$139.99

The Cadet Register Plus premier fan-forced heater is often chosen for its similar appearance to a central system register vents. A large squirrel cage blower quietly provides increase airflow allowing for lower surface and air-at surface temperatures. The wall can is designed for quick installation with mounting legs that minimize measuring time. Primary Heating Application: Wall heater, BTU Output: 6,820 / 5,115, Volts: 240 / 208, Amps: 8.33 / 7.21, Watts: 2,000 / 1,500, Blower Included: Yes, Thermostat Included: No, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: High temperature manual reset turns off heater if normal operating temperatures are exceeded, Dimensions W x D x H (in.): 14 x 4 x 7 2000 Watts @ 240V; 1500 Watts @ 208V Rough-in Dimensions: 12 3/4in.W x 4in.D x 6in.H Commercial-grade steel element Thermostat required (not included) [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

US Stove Freestanding Multifuel Heater, Model# 6041

$1,699.00

This omnivorous heater can burn corn or pellets out of the box and can be adapted to burn soybeans, cherry pits, olive pits, bio mass fuel grains and processed silage. Great for those who want to reduce waste while they stay warm. U.S.A. BTU Output: 53,300, Fuel Type: Corn / pellet, Blower Included: Yes, Blower (CFM): 200, Full Load Run Time (Hours): 30, Heating Capability (sq. ft.): 2,000, Igniter: Yes, Thermostat Included: No, Fire Box/Hopper Capacity (lbs.): 60, Door Opening W x H (in.): 19 3/4 x 11 11/16, Clearance from Rear Wall (in.): 9, Dimensions W x D x H (in.): 27 3/4 x 30 1/2 x 30 3/4 Blower controlled by LED control panel Built-in diagnostics Easy ash removal with large ash pan [Read more]

Store: Northern Tool and Equipment

Brand: US Stove Company

Ouellet Residential Radiant Cove Heater - 120 Volts, 1-Phase, 450 Watts, Model# ORC0452BL

$89.98

Small residential and light commercial heater that you can install on the wall to heat where space limitations wont allow you to install a conventional heater. Great for use in nursery, laundry room, bathroom or workshop. In White. Primary Heating Application: Radiant, Volts: 120, Amps: 3.75, Watts: 450, Heat Settings: No, Thermostat Included: No, Power Cord (ft.): Must be hardwired, Remote Included: No, Thermal Cutoff Safety Device: No, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 36 x 4 x 7 120 Volts, single-phase Front made of aluminum extrusion profiled to increase radiating surface Back of unit made with 18-gauge painted steel Large junction box on each end with connector for quick installation Wall installation bracket doesnt require opening units housing Stainless steel tubular heating element inserted into a solid aluminum extrusion preventing any thermal expansion noise 6ft. minimum clearance to floor; 4 1/2in. minimum to ceiling [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

Ouellet Residential Radiant Cove Heater - 59in, 750W/240V, Model# ORC0750BL

$179.99

The Ouellet Residential Radiant Cove Heater can be installed in residential and light commercial settings where space limitations prevent the installation of a conventional heater. Primary Heating Application: Radiant, Volts: 240, Amps: 3.13, Watts: 750, Heat Settings: No, Thermostat Included: No, Power Cord (ft.): Must be hardwired, Remote Included: No, Thermal Cutoff Safety Device: No, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 61 x 4 x 7 White Can be installed in settings where space limitations prevent installation of a conventional heater Stainless steel tubular heating element housed in aluminum extrusion prevents thermal expansion noise and profiled to increase radiating surface Junction box on each end and wall installation brackets make for quick installation Requires 6-ft. minimum clearance to floor and 4.5in minimum from ceiling [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

BioSmart In-Wall Infrared Heater - 5200 BTU, Model# BIO-1000F

$499.98

This BioSmart in-wall infrared heater delivers powerful heating in a slim-lined package. Up to 160 F of therapeutic infrared heat. The chassis stays cool to the touch with insulation that exceeds all government and independent safety standards. Must be hardwired. Works with any 12-24V thermostat (not included). Overheat safety cutoff device. Primary Heating Application: Wall heater, BTU Output: 5,200, Heating Capability (sq. ft.): 500, Watts: 1,000, Blower Included: Yes, Thermostat Included: No, Remote Included: No, Thermal Cutoff Safety Device: Yes, Dimensions W x D x H (in.): 12 1/2 x 3 1/2 x 15 [Read more]

Store: Northern Tool and Equipment

Brand: Comfort Zone

Blower for ProCom Heaters and Stoves, Model# QEB100

$99.98

Blower will help circulate heat 75% better. Auto and Manual: Yes, Works With: ProCom heaters and stoves, Dimensions L x W x H (in.): 10 x 4 x 2 1/2, Includes: 1 Blower [Read more]

Store: Northern Tool and Equipment

Brand: Procom

Cadet Perfectoe Electric In-Wall Heater - 240V, 1000 Watt, Black, Model# UC102B

$169.99

The Cadet Perfectoe Under Counter Electric In-Wall fan-forced heater is the ideal solution for areas with limited wall space. The Model UC102B can be placed in areas with restricted space as in bathrooms, stairwells and hearths, or install in under-cabinet applications in kitchens. Quietly provides instant warmth for a cold room. Primary Heating Application: Wall heater, BTU Output: 3,412 / 2,557, Volts: 240 / 208, Amps: 4.17 / 3.61, Watts: 1,000 / 750, Blower Included: Yes, Thermostat Included: No, Receptacle Type Required: Hardwire, Thermal Cutoff Safety Device: High temperature manual reset turns off heater if normal operating temperatures are exceeded, Dimensions W x D x H (in.): 18 x 8 1/4 x 3 1/2 1000 Watts @ 240V; 750 Watts @ 208V Rough-in dimensions: 14 1/2in.W x 8 1/4in.D x 3 1/2in.H Minimum distance: 6in. from an inside corner surface A wall mounted thermostat is recommended for optimum performance (sold separately) [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Cadet Electric Baseboard Heater - 240 Volt, 1500 Watt, White, Model# 6F1500W

$59.99

The Cadet 1500 Watt Electric Baseboard Heater is the ideal choice for low-cost installation, while quiet operation and welcome comfort make it the preferred heater for bedrooms, utilizing convection to circulate air. Easy to install for remodel, new construction, or cold room applications. Primary Heating Application: Baseboard, BTU Output: 5,115 / 1,125, Volts: 240 / 208, Amps: 6.25 / 5.41, Watts: 1,500 / 1,125, Blower Included: No, Heat Settings: 1, Thermostat Included: No, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: Oversized high temperature limit switch with full-length capillary sensor tube, Dimensions W x D x H (in.): 72 x 2 1/2 x 6 3/4 1500 Watts @ 240V; 1125 Watts @ 208V Size: 72in.W x 2 1/2in.D x 6 3/4in.H Easy installation with pre-punched case at 1in. intervals Powder-coated paint for a smooth, premium finish Rugged steel construction increases durability Works best when placed under a window with 3ft. clearance in front; 12in. above; 6in. to sides Thermostat required (sold separately) [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

TPI Suspended Salamander Heater - 51,195 BTU, 480 Volt, Model# YES-1524-1A

$799.98

This TPI Suspended Salamander Heater hangs from walls or ceilings of garages, workshops or any place a constant temperature is desired. U.S.A. Primary Heating Application: Construction, garage, BTU Output: 51,195, Heating Capability (sq. ft.): 2,000, Volts: 240, single-phase, Amps: 63, Watts: 15kW, Blower Included: Yes, Blower (CFM): 800, Heat Settings: Thermostat, Thermostat Included: Yes, Plug Type: Hard wire, Remote Included: No, Tip-Over Safety Switch: Yes, Dimensions W x D x H (in.): 24 x 24 x 36 Made of 20-gauge steel with front and rear wire mesh guards Powder coated in safety yellow Magnetic switch allows for fan only operation Includes blower, thermostat, thermal cutoff safety device and mounting hardware For indoor use only [Read more]

Store: Northern Tool and Equipment

Brand: TPI

TPI Indoor/Outdoor Quartz Infrared Heater - 16,382 BTU, 240 Volts, Stainless Steel, Model# 223-90-TH-240V

$599.98

This TPI Indoor/Outdoor Quartz Infrared Heater offers the same powerful heat as the heaters used at bus stops. Industrial-grade quartz infrared heater instantly delivers generous amounts of heat when you need it and cools down fast when you dont. Rugged 20-gauge steel withstands years of use, indoors or outdoors great for sheds, barns, workshops, outdoor work areas and more. Gold anodized aluminum reflectors and porcelain end caps provide 97% efficient reflectivity, broadcasting a wide 90 pattern. Resistant to moisture and thermal shock. Coiled tungsten filament in a sealed halogen-filled quartz envelope. 6in. wire pigtail leads. Stainless steel. ETL listed housing. Requires hardwired connection. U.S.A. Primary Heating Application: Outdoor overhead and indoor industrial heating, BTU Output: 16,382, Volts: 240, Watts: 4.8kw, Blower Included: No, Thermostat Included: No, Plug Type: Hardwire, Dimensions W x D x H (in.): 15 x 33 x 11 Same powerful heat as the heaters used at bus stops Instantly delivers heat when you need it and cools down fast when you dont Rugged 20-gauge steel withstands years of use, indoors or outdoors Gold anodized aluminum reflectors and porcelain end caps provide 97% efficient reflectivity, broadcasting a wide 90 pattern Resistant to moisture and thermal shock Coiled tungsten filament in a sealed halogen-filled quartz envelope Stainless steel [Read more]

Store: Northern Tool and Equipment

Brand: TPI

Ouellet Residential Wall Heater - 2000 Watt, 240/208V

$114.98

This high-efficiency fan-forced heater with thermostat is designed for areas where space is limited, like hallways, basements, kitchens, bathrooms and stairwells. It features a silent axial fan that blows air over a durable heating element to circulate warm air throughout room. The clean lines and rounded corners of this heater will match perfectly with all interior styles. Primary Heating Application: Wall heater, Volts: 240/208, Amps: 8.34/7.22, Watts: 2,000/1,500, Blower Included: yes, Blower (CFM): 80, Heat Settings: Yes, Thermostat Included: Yes, Power Cord (ft.): Must be hardwired, Remote Included: No, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 8 1/8 x 3 x 16 2000 Watt 240/208V single phase Quiet fan operating @ 41.3 dBA @ 80 cfm Can be mounted 4 ways into wall to circulate air vertically or horizontally Durable tubular heating element with fins For surface mounting, use Item# 173023, sold separately Hardwired 20 gauge steel 8.125in.W x 3in.D x 16in.H White [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

Cadet Register Plus Heater - Box Only, 120 Volt, 500/1000/1500 Watt, Model# RM151

$119.98

The Cadet Register Plus is a premier fan-forced heater often chosen for its similar appearance to a central system register vents. A large squirrel cage blower quietly provides increase airflow, allowing for lower surface and air-at-surface temperatures. Designed for ease of installation. Primary Heating Application: Wall heater, Volts: 120, Amps: 4.17 / 8.33 / 12.5, Watts: 500 / 1000 / 1500, Blower Included: Yes, Thermostat Included: No, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: High temperature manual reset turns off heater if normal operating temperatures are exceeded, Dimensions W x D x H (in.): 12 x 7 1/2 x 5 3/4 Heater assembly only; wall can, grill and thermostat not included 500/1000/1500 Watts @ 120V Rough-in dimensions: 12 3/4in.W x 4in.D x 6in.H Commercial-grade steel element [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Ouellet Portable Unit Heater - 3000 / 4000 Watt, 208 / 240V, 1 Phase, Model# OHV04000CC

$399.98

The Ouellet portable unit heater produces 310 CFM and a temperature rise of up to 51 F in spaces up to 500 sq. ft. Primary Heating Application: Construction, garage, BTU Output: 13,648, Heating Capability (sq. ft.): 500, Volts: 240, Amps: 16.67, Watts: 4,000, Blower Included: Yes, Blower (CFM): 310, Heat Settings: Yes, Thermostat Included: Yes, Power Cord (ft.): 6, Plug Type: Nema6-20P, Receptacle Type Required: Grounded 3 pronged 20 amp, 250vac, 240 volt outlet, Remote Included: No, Thermal Cutoff Safety Device: Yes, Tip-Over Safety Switch: No, Dimensions W x D x H (in.): 22 x 14 x 21 Includes wall/ceiling/floor mounting brackets for permanent installation if desired Designed for use in garages, workshops, storage areas, utility rooms and/or light commercial applications Not intended for use within a living space such as a family room, bedroom or room within a house In red/black [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet

Lanair Ductable Waste Oil Heater - 300,000 BTU, Model# MXD300 (DUCTABLE)

$5,199.99

Cut your petroleum dependency back and stay warm by burning used crankcase, hydraulic and transmission oil. This super-powered heater produces a ton of heat to warm a very large space. U.S.A. Not for sale in California. BTU Output: 300,000, Heating Capability (sq. ft.): 15,000, Volts: 120, Amps: 20, Blower (CFM): 1,696, Fuel Type: Waste oil, Fuel Consumption (gal./hr.): 2.08, Thermostat Included: Yes, Chimney Pipe Size (in.): 8, Chimney Type: Class A, Dimensions L x W x H (in.): 54 x 46 x 36 Burns Used W10-W50 crankcase oil 2.08 GPH fuel input [Read more]

Store: Northern Tool and Equipment

Brand: Lanair

Cadet Compak Plus Heater - Box Only without Thermostat, 240 Volt, 2000 Watt, Model# CS202

$89.98

The Cadet ComPak Plus In-Wall fan-forced heater is perfect for smaller areas or larger areas needing the dispersed heat created by multiple heaters. This ComPak Plus heater takes up less space than baseboards or larger in-wall heaters with its unique, compact design. Quietly provides instant warmth and comfort to a cold room. Primary Heating Application: Wall heater, BTU Output: 6,820 / 5,115, Volts: 240 / 208, Amps: 8.33 / 7.21, Watts: 2,000 / 1,500, Blower Included: Yes, Heat Settings: 1, Thermostat Included: No, Receptacle Type Required: Hardwire, Thermal Cutoff Safety Device: Primary 16 Amp rating manual power reset @ 240V, with over-temperature thermal back-up fuse, Dimensions W x D x H (in.): 7 7/8 x 4 x 11 1/2 Heater assembly only; thermostat, wall can and grill sold separately 2000 Watts @ 240V; 1500 Watts @ 208V Nichrome coil element for quick heat Quiet, 2-stage centrifugal blower Primary and secondary thermal safeguards Replaces C or CS series in-wall heaters Clearance: 3ft. in front, 12in. above, 6in. to sides [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Cadet ComPak Plus Electric In-Wall Heater - 120V, 1000 Watt, White, Model# CSC151TW

$109.98

The Cadet ComPak Plus In-Wall fan-forced heater is perfect for smaller areas or larger areas needing the dispersed heat created by multiple heaters. The Model CSC151TW takes up less space than baseboards or larger in-wall heaters with its unique, compact design. Thermostat included. Quietly provides instant warmth and comfort to a cold room. Primary Heating Application: Wall heater, BTU Output: 5,115, Volts: 120, Amps: 12.5, Watts: 1,500, Blower Included: Yes, Heat Settings: 1, Thermostat Included: Yes, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: Primary 16 Amp rating manual power reset @ 240V, with over-temperature thermal back-up fuse, Dimensions W x D x H (in.): 9 x 4 x 12 1000 Watts @ 120V Rough-in dimensions: 8in.W x 4in.D x 10 1/4in.H Nichrome coil element for quick heat Quiet, 2-stage centrifugal blower Primary and secondary thermal safeguards Powder-coated wall can eliminates sharp edges Premium-finish white grill Clearance: 3ft. in front, 12in. above, 6in. to sides [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

SunStar Heating Products Garage Tube Heater - LP, 25,000 BTU, Model# SIR25-15-L

$729.98

The SunStar Garage Tube Heater is ideal for residential garages, vestibules, entryways, workshops, enclosed patios, restaurants, smoking shelters, small greenhouses, hard-to-heat small areas and low-ceiling height applications. Low intensity radiant heat can save up to 30% in fuel savings over convection warm air heating. Heaters can be controlled by a line voltage thermostat (sold separately). If preferred, the heaters can be controlled by a 24V Thermostat and a 24V Thermostat Relay Kit (both sold separately). U.S.A. NOTE: In residential garage applications, the heater must be vented outside through sidewall or the roof. In commercial/industrial space heating applications, the heater can be indirectly vented (optional exhaust hood sold separately). Please review the detailed Installation & Operating Instructions (attached) for other specific installation requirements (gas pressure, ventilation etc.) prior to purchasing the heater. Vent-Free: No, BTU Output: 25,000, Heating Capability (sq. ft.): 500 - 15,000, Primary Heating Application: Garage, workshop, Blower Included: No, Heat Settings: Thermostatically controlled, Fuel Type: Propane, Fuel Consumption (gal./hr.): 0.2, Gas Inlet (in.): 1/2, Igniter: Direct spark, Thermostat Included: No, Remote Included: No, Dimensions W x D x H (in.): 110 x 18 x 10 Compact size: overall length is 110in. for ease of installation Efficiencies range up to 84.5% Installation as low as 8ft. above floor CSA design certified Vacuum System pulls combustion products through the combustion chamber for greater safety, virtually eliminating the possibility of combustion gases leaking into the heated space Solid State Ignition System offers reliable electronic direct spark ignition system with 100% gas safety shutoff control and 30-second pre-purge U-Tube Design provides uniform emitter tube temperatures and energy distribution on the floor, unlike straight tube heaters which are always hotter at the burner end than at the exhaust end... [Read more]

Store: Northern Tool and Equipment

Brand: SunStar

HouseWarmer Slim-Profile Direct-Vent Wall Heater with Built-In Blower - 18,000 BTU, Propane, Model# HWDV181BDVP

$399.00

Slim-profile design is less obtrusive and more attractive than traditional vented heaters. Heater requires no electricity so it will even work in a power failure (electricity required for blower). 115V, .4 Amp blower has 4-ft. electric cord for a standard wall outlet. Use in accordance with local codes and ordinances. U.S.A. BTU Output: 18,000, Primary Heating Application: Wall, Blower Included: Yes, Fuel Type: Propane, Thermostat Included: Yes, Dimensions W x D x H (in.): 22 1/4 x 9 3/8 x 25 1/4 Mounts on any outside/exterior wall from 4 1/2in-12in. thick Built-in blower Thermostat Thermocouple safety valve Heater requires no electricity (electricity required for blower) 115V, .4 Amp blower has 4-ft. electric cord for a standard wall outlet Easy to install 10-year limited warranty on heat exchanger; 1 year on balance of product [Read more]

Store: Northern Tool and Equipment

Brand: Housewarmer

Cadet Register Plus Heater - Box Only, 240 Volt, 2000 Watt, Model# RM202

$119.98

The Cadet Register Plus is a premier fan-forced heater often chosen for its similar appearance to a central system register vents. A large squirrel cage blower quietly provides increase airflow, allowing for lower surface and air-at-surface temperatures. Designed for ease of installation. Primary Heating Application: Wall heater, Volts: 240 / 208, Amps: 6,820 / 5,115, Watts: 2,000 / 1,500, Blower Included: Yes, Thermostat Included: No, Receptacle Type Required: Hardwire, Remote Included: No, Thermal Cutoff Safety Device: High temperature manual reset turns off heater if normal operating temperatures are exceeded, Dimensions W x D x H (in.): 12 5/8 x 4 x 6 7/8 Heater assembly only; wall can, grill and thermostat not included 2000 Watts @ 240V; 1500 Watts @ 208V Rough-in dimensions: 12 3/4in.W x 4in.D x 6in.H Commercial-grade steel element [Read more]

Store: Northern Tool and Equipment

Brand: Cadet

Soleus Portable Air Conditioner with Heater - 12,000 BTU, Model# PH3-12R-03

$529.98

The Soleus Portable Air Conditioner includes a 12,500 BTU Heater, making this a multiseasonal unit to take the place of several appliances, saving space and energy. Evaporative technology reduces the need to drain condensate. Designed to efficiently cool, dehumidify, or heat any space without permanent installation. Application: Air conditioner, BTU Cooling: 12,000, BTU Heating: 12,500, Capacity: 60 pints / day, Volts: 115, CFM: 240, Dimensions L x W x H (in.): 13 x 22 x 27 3/4, Speeds (qty.): 3, Temperature Range ( F): 64 - 90, Timer: 24-hr. programmable, Watts: 1,100 Electronic controls with LED Remote control Dual hose exhaust Heavy-duty casters Washable filter [Read more]

Store: Northern Tool and Equipment

Brand: Soleus

Ouellet Residential Radiant Cove Heater - 240 Volts, 1-Phase, 450 Watts, Model# ORC0450BL

$89.98

Small residential and light commercial heater that you can install on the wall to heat where space limitations wont allow you to install a conventional heater. Great for use in nursery, laundry room, bathroom or workshop. In White. Primary Heating Application: Radiant, Volts: 240, Amps: 1.88, Watts: 450, Heat Settings: No, Thermostat Included: No, Power Cord (ft.): Must be hardwired, Receptacle Type Required: No, Remote Included: No, Thermal Cutoff Safety Device: No 240 Volts, single-phase 450 Watts 34in. long Front made of aluminum extrusion profiled to increase radiating surface Back of unit made with 18-gauge painted steel Large junction box on each end with connector for quick installation Wall installation bracket doesnt require opening units housing Stainless steel tubular heating element inserted into a solid aluminum extrusion preventing any thermal expansion noise 6ft. minimum clearance to floor; 4 1/2in. minimum to ceiling [Read more]

Store: Northern Tool and Equipment

Brand: Ouellet